Stylus Pro 5000 RIP Station
Service Guide

$8.99
Stylus Pro 5000 RIP Station<br> Service Guide
   Click to enlarge
      

This guide is divided into the following sections:

• “Preface”
Gives general information about this guide and about installing the RIP Station 5000.

• Chapter 1, “Introduction”
Provides general information about the RIP Station 5000.

• Chapter 2, “Preparing for Installation”
Describes unpacking and the steps you need to take before you install the unit.

• Chapter 3, “Connecting the RIP Station 5000”
Describes how to connect the RIP Station 5000 to the printer and the network and verify that the system is working correctly. This chapter also gives an overview of the Control Panel.

• Chapter 4, “Service Procedures”
Describes removal and replacement procedures for RIP Station 5000 components.

• Chapter 5, “Troubleshooting Procedures”
Identifies the source of common problems and suggests ways of correcting them.



Chapter 1: Introduction
Features
How the RIP Station 5000 operates
Print options
Remote utility software
User Software CD
Fiery WebTools

Chapter 2: Preparing for Installation
The installation sequence
Checking the customer site
Setting customer expectations
Unpacking the RIP Station 5000
RIP Station 5000 front and back panels

Chapter 3: Connecting the RIP Station 5000
Preliminary checkout
Connecting to the printer
Printing the RIP Station 5000 Test Page
Connecting to the network
Connecting a PC-compatible to the parallel port
Using the Control Panel
Activity light
Buttons
Screens and icons
Shutting down and restarting the RIP Station 5000

Chapter 4: Service Procedures
Overview
Accessing internal components
Checking internal connections
Restoring functionality after service
Removing and replacing circuit boards
User interface board
Motherboard
Fans
Power switch
Power supply
Checking voltages
Hard disk drive
Front panel components
System Software Kit
Using the SCSI port 3
Using the parallel port
Software not authorized screen 4

Chapter 5: Troubleshooting Procedures
The troubleshooting process
Where problems occur
Before you go to the customer site
Preliminary on-site checkout
Checking the interface cables
Checking the internal components
Checking the RIP Station 5000 as a stand-alone unit
Isolating the RIP Station 5000
Errors during the Start-up diagnostics
General RIP Station 5000 system error conditions
RIP Station 5000’s diagnostic sets
Start-up diagnostics
Viewing the diagnostic report
Checking the entire RIP Station 5000 system
Checking the printer interface
Checking network connections
Printing to the RIP Station 5000


FORMAT: High resolution PDF document!
ZIP archive: 3 349 kB

I want to:

Any questions about this product?

SEND US REQUEST by filling the form below.





Step 1
ADD TO CART
Step 2
CHECKOUT
Select payment method.
Step 3
Confirm the order.


We are in business since 2002 and do our best to give our customers perfect service!

  Paul Jumbo 2019-04-19 18:47:57  
  I had Epson WF-2650 and it wasn't printing fully, skipping lines, even though colors were full.
I did a lot of cleaning, head cleaning, put new cartridge but no luck. I did some head cleaning using glass cleaner and syringes as shown on various youtube video.
After that, my printer didn't recognize two of the cartridges. I tried everything, cleaning contacts etc, nothing worked.

I was finally going to buy new cartridges however stores were closed today so I decided to look for chip-resetting tool but nothing good was available locally.

I came across this WIC reset utility and was really skeptical if it will work. I took the chance, bought the key, used the tool to reset firmware to chipless firmware, it was successful at the first go.
At this point, printer showed all ink levels 100%. I printed a test page and it came out perfect.
To make it even more interesting for me, I live in Europe and during one of the trip, I bought two sets of XL cartridges for this same model but printer didn't recognize in the past and I was going to throw them since these were no good for my EU model. I tried these again after chip reset firmware and voila, they works too.

I am amazed at the propaganda of these printer manufactures that even original printer cartridges from US didn't work on the model here in EUROPE, these used to fit perfectly but printer wouldn't recognize however, now they works too.
Today, I was almost ready to trash my 2.5 yr old and not much used printer but after a lot of trying and finally using WIC reset utility, the printers works like new and saved me a lot!

These were the best 20 CHF/USD I spent today!
Thank you very much and I don't need to worry about relying on a hardware chip-reset tool. I will now be able to use US model cartridges and re-fill i like without having to worry. I even printed some photos using this same printer on photo paper today and printer did an excellent job.
  Park Chan Yong 2007-11-16 06:30:19  
  yes!
  Darius Sruoginis 2025-02-03 17:37:11  
  Changed the waste ink pads with the new ones and used WicReset for reseting waste counter on Epson L382. Received the key without any delay, right after placing the order and paying for it. Worked perfectly. Counter became 0,00%. Great utility!
  coca cristi 2011-12-13 20:13:48  
  multumesc mult! pentru ajutorul acordat imprimanta mea functioneaza iarasi.
  rdlaw law 2023-01-19 22:37:39  
  It was best $10 I ever paid in my life!!!
  Ng Jong Hwa 2005-03-08 07:17:37  
  very good!
  amprenta clau 2016-12-22 13:14:48  
  Foarte multumit, am cumparat on-line in 22 decembrie 2016 - codul (Key) - a durat 5-10 minute (inregistrarea pe site si plata), am instalat softul lor in care am introdus codul primit prin e-mail - de la ei si in cateva secunde totul functioneaza ca nou. Imprimanta mea Epson R285 - resetata acum a 2-a oara. Prima data, de frica am apelat la o persoana, care tot aici a resetat-o. Recomand cu drag. Thank You, I recommended Very pleased, I bought online in the December 22, 2016 - code (Key) - lasted 5-10 minutes (registration and payment on site), I installed their software in which we introduced code received via e-mail - from her and within seconds everything works like new. My Epson R285 printer - now reset the 2nd time. First, the fear I turned to someone who here has reset it. I recommend
Write review